![]() Make sure you turn each bolt slowly as not to strip the threads on the bolts. If your overflow cover is a metal grate, you may be able to tighten it down with a flat head screwdriver or Allen key. ![]() Do this slowly so that you don’t strip out the threads on the cap or grate your knuckles on the sharp edges.ģ. If your tub has a metal screw cap covering the overflow drain, try tightening it down with an adjustable wrench. If this is the case, usually, you can push on the far side of the disk to tighten it up.Ģ. For example, some tubs have a large plastic disk attached to a small metal nipple with a rubber o-ring that runs out from the center of the disk. Check to make sure the overflow cover is broken. Here are some tips and suggestions on how to seal bathtub overflow.ġ. Plus, you can even tighten the screws on both sides of the overflow drain cover to make sure that it’s completely secure. This will make sure that the overflow area is properly sealed and secure. Step 11: Tighten The Screws Completelyįinally, you can tighten the locking screws all the way so that there’s no space between the overflow drain cover and the plumber’s putty. Now that your overflow area is properly sealed and secured, you won’t have to worry about water spilling out and causing damage to your bathroom. Next, place the rubber around the overflow drain faucet to create a tight seal that will prevent water from spilling out. Once the plumber’s putty has dried, you can remove the old gasket and replace it with a new one. This will also help ensure that the plumber’s putty does not stick onto your hands during the process. You’ll need about 30 minutes for it to dry correctly, so make sure you get started on this task early enough in advance. It would help if you allowed the plumbing putty to dry completely before continuing with the next step of this process. However, be sure that you don’t tighten them too much just yet you’ll want to insert the plumber’s putty, so there is a secure seal between the overflow plate and your bathtub. You can then screw on the locking screws onto both sides of the overflow drain cover. Be sure to push firmly so that it fits securely over the faucet. Once you have your new overflow drain cover in hand, go ahead and place it over the drain hole of your bathtub. Step 8: Secure The Cover With Screws And Plumbing Putty Now that your tub’s overflow drain area is covered and sealed correctly, there’s no need to worry about water spilling out. It should not pop out when pressure is applied to it otherwise, water will begin spilling over the hole again. Once the overflow drain cover is in place, you must ensure that it maintains its seal throughout the entire time. You can use a wet rag to wipe away any dirt and dust in this area before inserting a new overflow cover. Step 6: Clean The Areaīefore you put in your new overflow cover, it’s important to clean the area around the drain so that no dirt or debris from the old cover will be transferred onto it when you remove it. Be sure that you don’t break it while you attempt to remove it, or else you will have to replace the entire plumbing system of your bathtub. This is usually located right below the drain cover, so it will be easy to take off. You’ll have to remove the old overflow plate and bracket on your bathtub. Step 5: Remove the Old Overflow Plate and Bracket You’ll have to use a pair of scissors and trim off the excess portion of the overflow drain cover. Step 4: Cut Drain Opening If NecessaryĪt this point, it’s essential to cut the overflow drain cover if you need to fit it around your bathtub faucet. But, again, be sure to push firmly so that it fits securely over the faucet. Once you have your overflow drain cover in hand, you can place it over the drain hole that’s located on the side of your bathtub near the faucet. Step 3: Place The Cover Over The Drain Hole Just make sure you choose one that fits your bathtub’s size for example, if your tub is 10 inches in diameter, you’ll need a smaller-sized cover than a 15-inch cover. There are also downspout drain covers, which work the same way as overflow covers do. There are many different bathtub overflow drain covers that you can use to prevent water from spilling out over the hole. The hole in this area is where all excess water runoff goes through when it starts to overflow. It will be located on the side of your tub near the faucet closest to the wall. ![]() Step by Step Guide: How to Seal Bathtub Overflow Step 1: Use A Bathtub Overflow Drain Coverįirst, you must locate the overflow drain of your bathtub. Angle grinder with the diamond blade attachment.How to change a bathtub overflow drain seal? Require Tools and Materials:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |